Control valve with chemical-resistant, vacuum-proof lining

DIN-EN: DN 15 – 200 / PN 10 – 40
ASME: NPS ½“ – 8“ / class 150
PT range: -30 < T < 230°C, vacuum 10^-8 mbar

Design Features

Design Features

Design Characteristics

different KVS values
individual control characteristics
free passage possible with open valve
equal percentage or linear characteristic line
cost-effective automation
readily reproducible control position

The construction of the RH-A control valves is based on our standard cavity-free plug valve with chemical resistant PFA/FEP-lining. A wide range of materials for housings, plugs, as well as for sleeves or linings are available for different areas of application. If required, the control valves can also be supplied with a heating jacket.

PT-Diagram

PT-Diagram

The specified values depend on the respective application (medium). Operating temperatures under -20°C only with body material 1.4408 or low-temperature steel. Hight pressure resistance / temperature resistance on request, e.g. PN 40.

Sleeve: There are different sleeve materials / compounds available.

Materials

Materials

Standard body materials
• Ductile cast iron ENJS 1049, ASTM Gr 60-40-18 / A395

Standard plug materials
• Stainless Steel 1.4308, ASTM A351 CF8

Special materials
• Carbon Steel 1.0619, ASTM A216 WCB
• Stainless Steel 1.4408, ASTM A351 CF8M
• Unalloyed stainless steel casting (low Temp.) 1.1138, LCC/LCB/A352

Lining materials
• Body: PFA, PFA-conductive, FEP
• Plug: PTFE, PFA, PFA-conductive, FEP

Sealing Systems

Sealing Systems

Chemical sealing to prevent fugitive emission of aggressive and toxic media
with PTFE packing for additional stem sealing; T_max 230°C

Type CA

Type CASN-A

Port Forms

As standard, there are ten plugs forms available per valve size, consisting of five linear and five equal percentage control characteristics.

Furthermore, bespoke plug forms can be calculated and designed according to customer-specific requirements that combine, for example, control properties and free passage.

Characteristics

Characteristics

Type RH-A, linear control characteristics

Type RH, equal percentage control characteristics

Model structure
The data was determined by flow simulation and based on the VDI/VDE 2173 with a permissible deviation of +/- 10% (medium = water 20°C, pressure loss Δp = 1 bar).

Definition Kvs
The Kvs value designates the maximum possible throughput for a valve with a 100% opening

Definition Kv
The flow coefficient Kv [m³/h] is a specific volume flow for the following conditions:
– The pressure loss (Δp) via the valve is 10⁵ Pa (1 bar)
– The medium is water with a temperature between 278 K and 315 K (5°C to 40°C)

Definition Cv
The flow coefficient Cv is a valve flow coefficient that does not correspond to S.I. units. It represents the number of U.S. gallons of water which flow through a valve with a pressure loss of 1 psi (68.95 mbar) at a temperature of 40°F to 100°F (4°C to 38°C) within a minute. Cv = Kv/0,865

Actuation

Actuation

1 Locking Devices
Pilot valve combinations, pad lock eyelets, linear key conception, indexing plunger arrestor.
read more […]

2 Plug stem extension
Solid construction in stainless steel with T-wrench, Standard extension 100 mm or 150 mm, non standard lengths are available on request
read more […]

3 Actuators
Actuators for mounting-flange acc. to DIN ISO 5211
read more […]

NEW: Pneumatic actuator AIR GEAR for plug valves with high torque ≥150.000 Nm
read more […]

4 Ratched coupling
To usw on multiport valves with standard 90° actuator for bigger switchpositions than 90°
read more […]

5 Cover extension
Solid construction in stainless steel, Standard extension 100 mm or 150 mm high, non standard lengths are available on request . Hexagonal bolts on adjustment ring freely accessible. Note: Don’t use with sealing FSN/FSN-SL and CASN/CASN-SL
read more […]